Starting kernel ...
Uncompressing Linux..........................................................................................................................................
[ 0.000000] Linux version 2.6.32 (ubuntu@ip-10-204-115-71) (gcc version 4.3.3 (GCC) ) #3 PREEMPT Wed Aug 18 15:53:03 UTC 2010
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: OMAP3 Beagle Board
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] OMAP3630/DM3730 ES1.0 (l2cache iva sgx neon isp 192mhz_clk )
[ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
[ 0.000000] Reserving 16777216 bytes SDRAM for VRAM
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 117760
[ 0.000000] Kernel command line: console=tty0 console=ttyS2,115200n8 mem=80M@0x80000000 mem=384M@0x88000000 mpurate=1000 buddy=none camera=lbcm3m1 vram=12
[ 0.000000] Beagle expansionboard: none
[ 0.000000] Beagle cameraboard: lbcm3m1
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 80MB 384MB = 464MB total
[ 0.000000] Memory: 316288KB available (5880K code, 671K data, 204K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:402
[ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz
[ 0.000000] Reprogramming SDRC clock to 332000000 Hz
[ 0.000000] GPMC revision 5.0
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
[ 0.000000] Total of 96 interrupts on 1 active controller
[ 0.000000] OMAP GPIO hardware version 2.5
[ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty0] enabled
[ 0.000000] Calibrating delay loop... 494.72 BogoMIPS (lpj=1933312)
[ 0.000000] Mount-cache hash table entries: 512
[ 0.000000] CPU: Testing write buffer coherency: ok
[ 0.000000] tmpfs: No value for mount option 'mode'
[ 0.000000] devtmpfs: initialized
[ 0.000000] regulator: core version 0.5
[ 0.000000] NET: Registered protocol family 16
[ 0.000000] Beagle cameraboard: registering i2c2 bus for lbcm3m1
[ 0.000000] Found NAND on CS0
[ 0.000000] Registering NAND on CS0
[ 0.000000] Unable to get DVI reset GPIO
[ 0.000000] omap_init_mbox: platform not supported
[ 0.000000] Target VDD1 OPP = 4, VDD2 OPP = 2
[ 48.532165] OMAP DMA hardware revision 5.0
[ 48.538482] bio: create slab <bio-0> at 0
[ 48.539733] SCSI subsystem initialized
[ 48.541137] usbcore: registered new interface driver usbfs
[ 48.541290] usbcore: registered new interface driver hub
[ 48.541473] usbcore: registered new device driver usb
[ 48.541870] i2c_omap i2c_omap.1: bus 1 rev4.0 at 2600 kHz
[ 48.544525] twl4030: PIH (irq 7) chaining IRQs 368..375
[ 48.544586] twl4030: power (irq 373) chaining IRQs 376..383
[ 48.544891] twl4030: gpio (irq 368) chaining IRQs 384..401
[ 48.546630] regulator: VUSB1V5: 1500 mV normal standby
[ 48.546875] regulator: VUSB1V8: 1800 mV normal standby
[ 48.547149] regulator: VUSB3V1: 3100 mV normal standby
[ 48.550750] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
[ 48.551177] regulator: VMMC1: 1850 <--> 3150 mV normal standby
[ 48.551452] regulator: VDAC: 1800 mV normal standby
[ 48.551696] regulator: VPLL2: 1800 mV normal standby
[ 48.551971] regulator: VSIM: 1800 <--> 3000 mV normal standby
[ 48.552337] regulator: VAUX3: 1800 mV normal standby
[ 48.552673] regulator: VAUX4: 1800 mV normal standby
[ 48.552856] i2c_omap i2c_omap.2: bus 2 rev4.0 at 400 kHz
[ 48.560028] i2c_omap i2c_omap.3: bus 3 rev4.0 at 100 kHz
[ 48.561248] Switching to clocksource 32k_counter
[ 48.570220] musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
[ 48.570556] musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
[ 48.570587] musb_hdrc musb_hdrc: MUSB HDRC host driver
[ 48.570739] musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
[ 48.570892] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 48.570953] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 48.570983] usb usb1: Product: MUSB HDRC host driver
[ 48.571014] usb usb1: Manufacturer: Linux 2.6.32 musb-hcd
[ 48.571075] usb usb1: SerialNumber: musb_hdrc
[ 48.571716] hub 1-0:1.0: USB hub found
[ 48.571777] hub 1-0:1.0: 1 port detected
[ 48.572875] NET: Registered protocol family 2
[ 48.573120] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 48.573669] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 48.574096] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 48.574310] TCP: Hash tables configured (established 16384 bind 16384)
[ 48.574371] TCP reno registered
[ 48.574401] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 48.574432] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 48.574707] NET: Registered protocol family 1
[ 48.575164] RPC: Registered udp transport module.
[ 48.575195] RPC: Registered tcp transport module.
[ 48.575225] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 48.575531] Trying to unpack rootfs image as initramfs...
[ 48.578430] rootfs image is not initramfs (no cpio magic); looks like an initrd
[ 49.144317] Freeing initrd memory: 131072K
[ 49.145141] omap-iommu omap-iommu.0: isp registered
[ 49.146972] VFS: Disk quotas dquot_6.5.2
[ 49.147094] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 49.148345] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 49.149230] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 49.150085] msgmni has been set to 874
[ 49.153808] alg: No test for stdrng (krng)
[ 49.154144] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 49.154205] io scheduler noop registered
[ 49.154235] io scheduler deadline registered
[ 49.154388] io scheduler cfq registered (default)
[ 49.209930] OMAP DSS rev 2.0
[ 49.210021] OMAP DISPC rev 3.0
[ 49.210083] OMAP VENC rev 2
[ 49.210327] OMAP DSI rev 1.0
[ 49.546783] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 49.564544] serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
[ 49.581665] serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
[ 49.598754] serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
[ 50.198730] console [ttyS2] enabled
[ 50.209014] brd: module loaded
[ 50.215423] loop: module loaded
[ 50.219757] omap2-nand driver initializing
[ 50.224151] No NAND device found!!!
[ 50.227874] No NAND device found!!!
[ 50.232391] usbcore: registered new interface driver catc
[ 50.237915] catc: v2.8:CATC EL1210A NetMate USB Ethernet driver
[ 50.244018] usbcore: registered new interface driver kaweth
[ 50.249664] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
[ 50.257324] usbcore: registered new interface driver pegasus
[ 50.263031] rtl8150: v0.6.2 (2004/08/27):rtl8150 based usb-ethernet driver
[ 50.270080] usbcore: registered new interface driver rtl8150
[ 50.275878] usbcore: registered new interface driver asix
[ 50.281433] usbcore: registered new interface driver cdc_ether
[ 50.287414] usbcore: registered new interface driver dm9601
[ 50.293151] usbcore: registered new interface driver smsc95xx
[ 50.299072] usbcore: registered new interface driver gl620a
[ 50.304809] usbcore: registered new interface driver net1080
[ 50.310607] usbcore: registered new interface driver plusb
[ 50.316253] usbcore: registered new interface driver rndis_host
[ 50.322326] usbcore: registered new interface driver cdc_subset
[ 50.328399] usbcore: registered new interface driver zaurus
[ 50.334136] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[ 50.342224] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 50.349121] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[ 50.355194] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2
[ 50.362823] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
[ 50.381713] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[ 50.387634] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 50.394531] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 50.401855] usb usb2: Product: OMAP-EHCI Host Controller
[ 50.407226] usb usb2: Manufacturer: Linux 2.6.32 ehci_hcd
[ 50.412689] usb usb2: SerialNumber: ehci-omap.0
[ 50.417968] hub 2-0:1.0: USB hub found
[ 50.421844] hub 2-0:1.0: 3 ports detected
[ 50.452087] Initializing USB Mass Storage driver...
[ 50.457183] usbcore: registered new interface driver usb-storage
[ 50.463287] USB Mass Storage support registered.
[ 50.468353] mice: PS/2 mouse device common for all mice
[ 50.474029] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 50.481872] input: twl4030_pwrbutton as /devices/platform/i2c_omap.1/i2c-1/1-0049/twl4030_pwrbutton/input/input1
[ 50.492645] i2c /dev entries driver
[ 50.496765] Linux video capture interface: v2.00
[ 50.501770] omap-iommu omap-iommu.0: isp: version 1.1
[ 50.508178] vpfe_init
[ 50.511077] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
[ 50.624206] mmci-omap-hs mmci-omap-hs.1: err -16 configuring card detect
[ 50.631286] Registered led device: beagleboard::usr0
[ 50.636474] Registered led device: beagleboard::usr1
[ 50.642944] Registered led device: beagleboard::pmu_stat
[ 50.650054] usbcore: registered new interface driver usbhid
[ 50.655731] usbhid: USB HID core driver
[ 50.659790] Advanced Linux Sound Architecture Driver Version 1.0.21.
[ 50.666748] usbcore: registered new interface driver snd-usb-audio
[ 50.749511] usb 2-2: new high speed USB device using ehci-omap and address 2
[ 50.757293] No device for DAI omap-mcbsp-dai-0
[ 50.761810] No device for DAI omap-mcbsp-dai-1
[ 50.766326] No device for DAI omap-mcbsp-dai-2
[ 50.770812] No device for DAI omap-mcbsp-dai-3
[ 50.775329] No device for DAI omap-mcbsp-dai-4
[ 50.779846] OMAP3 Beagle SoC init
[ 50.784027] asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
[ 50.795501] ALSA device list:
[ 50.798614] #0: omap3beagle (twl4030)
[ 50.802551] oprofile: using arm/armv7
[ 50.806518] TCP cubic registered
[ 50.809814] NET: Registered protocol family 17
[ 50.814361] NET: Registered protocol family 15
[ 50.818939] lib80211: common routines for IEEE802.11 drivers
[ 50.824737] ThumbEE CPU extension supported.
[ 50.829071] Power Management for TI OMAP3.
[ 50.833892] Division by zero in kernel.
[ 50.837860] [<c0040c40>] (unwind_backtrace+0x0/0xdc) from [<c02542dc>] (Ldiv0+0x8/0x10)
[ 50.845977] [<c02542dc>] (Ldiv0+0x8/0x10) from [<df825f88>] (0xdf825f88)
[ 50.852783] Division by zero in kernel.
[ 50.856658] [<c0040c40>] (unwind_backtrace+0x0/0xdc) from [<c02542dc>] (Ldiv0+0x8/0x10)
[ 50.864807] [<c02542dc>] (Ldiv0+0x8/0x10) from [<df825f88>] (0xdf825f88)
[ 50.872161] Unable to set L3 frequency (400000000)
[ 50.877105] Switched to new clocking rate (Crystal/Core/MPU): 26.0/332/1000 MHz
[ 50.884490] IVA2 clocking rate: 800 MHz
[ 51.053558] SmartReflex driver initialized
[ 51.057708] Unable to handle kernel NULL pointer dereference at virtual address 00000014
[ 51.065856] pgd = c0004000
[ 51.068572] [00000014] *pgd=00000000
[ 51.072174] Internal error: Oops: 5 [#1] PREEMPT
[ 51.076843] last sysfs file:
[ 51.079803] Modules linked in:
[ 51.082885] CPU: 0 Not tainted (2.6.32 #3)
[ 51.087371] PC is at musb_interrupt+0x9f8/0xbb8
[ 51.091949] LR is at musb_interrupt+0x9e4/0xbb8
[ 51.096496] pc : [<c033df94>] lr : [<c033df80>] psr: 60000193
[ 51.096496] sp : df825e48 ip : df825e80 fp : 000000f0
[ 51.108062] r10: 00000000 r9 : 00000099 r8 : 00000009
[ 51.113311] r7 : 00000000 r6 : df81f108 r5 : 00000001 r4 : 00000000
[ 51.119903] r3 : 00000000 r2 : 00000000 r1 : fa0ab000 r0 : df81f108
[ 51.126464] Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
[ 51.133911] Control: 10c5387d Table: 80004019 DAC: 00000017
[ 51.139678] Process swapper (pid: 1, stack limit = 0xdf8242f0)
[ 51.145568] Stack: (0xdf825e48 to 0xdf826000)
[ 51.149963] 5e40: df825e90 00000000 00000001 00000004 df825eb0 df81f108
[ 51.158172] 5e60: 60000113 df892900 df824000 0000005c 00000000 00000000 c0667ac0 c033e1b8
[ 51.166412] 5e80: 0000000a df892900 c0635148 c00a33a0 00000001 df892900 c0635148 0000005c
[ 51.174652] 5ea0: 00000003 00000002 df824000 df825f45 df825f36 c00a5498 0000005c 00000000
[ 51.182891] 5ec0: df825f45 c003b074 c0630fe0 ffffffff fa200000 c003bb44 00000001 80000013
[ 51.191131] 5ee0: c0630fac c0630fac 00000001 0000000b df825f45 c067da23 0000001f 00000034
[ 51.199371] 5f00: df825f45 df825f36 df825ef8 df825f20 c006d254 c006d904 60000013 ffffffff
[ 51.207611] 5f20: 00000000 00000036 00000000 80000013 c0632080 205b6894 31352020 3335302e
[ 51.215850] 5f40: 5d383535 c0480020 df825f88 df825f88 00000000 df825f60 c01431e4 c0484188
[ 51.224090] 5f60: c0626930 c0626894 c0626930 c0626894 c06268d8 c0010668 00000001 00000000
[ 51.232330] 5f80: 00000000 00000000 00000000 c04838b0 00000001 c0010798 c056b1a5 00000000
[ 51.240539] 5fa0: 0000000c 00000001 c002fa10 0800fb70 00000001 c002f9b0 c002fa10 c003b374
[ 51.248779] 5fc0: 00000000 00000192 c0633484 00000000 00000000 c002f9b0 c002fa10 00000000
[ 51.257019] 5fe0: 00000000 c0008414 00000000 00000000 00000000 c003c9dc 04004002 00100080
[ 51.265258] [<c033df94>] (musb_interrupt+0x9f8/0xbb8) from [<c033e1b8>] (generic_interrupt+0x64/0x98)
[ 51.274566] [<c033e1b8>] (generic_interrupt+0x64/0x98) from [<c00a33a0>] (handle_IRQ_event+0xac/0x1ec)
[ 51.283935] [<c00a33a0>] (handle_IRQ_event+0xac/0x1ec) from [<c00a5498>] (handle_level_irq+0xbc/0x148)
[ 51.293334] [<c00a5498>] (handle_level_irq+0xbc/0x148) from [<c003b074>] (asm_do_IRQ+0x74/0x98)
[ 51.302093] [<c003b074>] (asm_do_IRQ+0x74/0x98) from [<c003bb44>] (__irq_svc+0x44/0xa8)
[ 51.310150] Exception stack(0xdf825ed8 to 0xdf825f20)
[ 51.315246] 5ec0: 00000001 80000013
[ 51.323455] 5ee0: c0630fac c0630fac 00000001 0000000b df825f45 c067da23 0000001f 00000034
[ 51.331695] 5f00: df825f45 df825f36 df825ef8 df825f20 c006d254 c006d904 60000013 ffffffff
[ 51.339965] [<c003bb44>] (__irq_svc+0x44/0xa8) from [<c006d904>] (vprintk+0x394/0x428)
[ 51.347930] [<c006d904>] (vprintk+0x394/0x428) from [<c04838b0>] (printk+0x18/0x28)
[ 51.355651] [<c04838b0>] (printk+0x18/0x28) from [<c0010798>] (omap3_sr_init+0x130/0x174)
[ 51.363891] [<c0010798>] (omap3_sr_init+0x130/0x174) from [<c003b374>] (do_one_initcall+0x5c/0x1bc)
[ 51.373016] [<c003b374>] (do_one_initcall+0x5c/0x1bc) from [<c0008414>] (kernel_init+0xa4/0x128)
[ 51.381866] [<c0008414>] (kernel_init+0xa4/0x128) from [<c003c9dc>] (kernel_thread_exit+0x0/0x8)
[ 51.390716] Code: e3530003 13a02000 05963078 05933018 (05d33014)
[ 51.396911] ---[ end trace 13892c89a1e825ea ]---
[ 51.401580] Kernel panic - not syncing: Fatal exception in interrupt